MN101CF95F, mn101cf95g ram ( 8-bit) rom ( 8-bit) type minimum instruction execution time standard: 0.2 s (at 2.7 v to 3.6 v, 10 mhz)* 0.5 s (at 2.7 v to 3.6 v, 4 mhz)* 62.5 s (at 2.7 v to 3.6 v, 32 khz)* double speed: 0.1 s (at 2.7 v to 3.6 v, 10 mhz)* interrupts ? reset watchdog external 0 external 1 external 2 external 3 external 4 external 5 timer 0 timer 1 timer 2 timer 3 timer 4 timer 5 timer 6 timer 7 timer 8 time base serial 0 reception serial 0 transmission serial 1 reception serial 1 transmission serial 2 serial 3 serial 4 reception serial 4 transmission automatic transfer finish a/d conversion finish key interrupts (12 lines) timer counter timer counter 0: 8-bit 1 (square-wave/8-bit pwm output, event count, pulse width measurement, serial clock output, real-time output control, generation of remote control carrier) clock source 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; external clock input interrupt source coincidence with compare register 0 timer counter 1: 8-bit 1 (square-wave output, event count, sync hronous output event, serial clock output) clock source 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; external clock input interrupt source coincidence with compare register 1 timer counter 0, 1 can be cascade-connected. timer counter 2: 8-bit 1 (square-wave output, pwm output, event count, pulse width measurement, synchronous timer, serial clock output) clock source 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of osc oscillation clock frequency; 1/1 of xi oscilla tion clock frequency; external clock input interrupt source coincidence with compare register 2 timer counter 0, 1, 2 can be cascade-connected. timer counter 3: 8-bit 1 (square-wave output, event count, serial clock output) clock source 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of osc oscillation clock frequency; 1/1 of xi oscilla tion clock frequency; external clock input interrupt source coincidence with compare register 3 timer counter 2, 3 can be cascade-connected. timer counter 0, 1, 2, 3 can be cascade-connected. timer counter 4: 8-bit 1 (square-wave/8-bit pwm output, event count, pulse width measurement, real-time output control, serial clock output) clock source 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; 1/1 of external clock input frequency interrupt source coincidence with compare register 4 package tqfp080-p-1212d *lead-free 128k 6k mn101cf95g (under development) mad00053aem MN101CF95F (under planning) 96k 4k
MN101CF95F, mn101cf95g timer counter (continue) timer counter 5: 8-bit 1 (square-wave/8-bit pwm output, event count, pulse width measurement, ser ial clock output) clock source 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; e xternal clock input interrupt source coincidence with compare register 5 timer counter 4, 5 can be cascade-connected. timer counter 6: 8-bit freerun timer clock source 1/1 of system clock frequency; 1/1, 1/128, 1/8192 of osc oscillation clock frequency; 1/1, 1/128, 1/8192 of xi oscillation clock frequency interrupt source coincidence with compare register 6 timer counter 7: 16-bit 1 (square-wave/16-bit pwm output, cycle / duty continuous va riable, event count, synchronous output evevt, pulse width measurement, input capture, real-time output control) clock source 1/1, 1/2, 1/4, 1/16 of system clock fr equency; 1/1, 1/2, 1/4, 1/16 of osc oscillation clock frequency; 1/1, 1/2, 1/4, 1/16 of external clock input frequency interrupt source coincidence with compare register 7 (2 lines) timer counter 8: 16-bit 1 (square-wave output, pwm output (duty continuous variable), event count, pulse width measurement, input capture) clock source 1/1, 1/2, 1/4, 1/16 of system cloc k frequency; 1/1, 1/2, 1/4, 1/16 of osc oscillation clock frequency; 1/1, 1/2, 1/4, 1/16 of external clock input frequency interrupt source coincidence with compare register 8 (2 lines) time base timer (one-minute count setting) clock source 1/1 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency interrupt source 1/128, 1/256, 1/512, 1/1024, 1/8192, 1/32768 of clock source frequency watchdog timer interrupt source 1/65536, 1/262144, 1/1048576 of system clock frequency serial interface serial 0: synchronous type / uart (full-duplex) 1 clock source 1/2, 1/4 of system clock frequency; pulse output of timer counter 1, 2; 1/2, 1/4, 1/16, 1/64 of osc oscillation clock frequency serial 1: synchronous type / uart (full-duplex) 1 clock source 1/2, 1/4 of system clock frequency; pulse output of timer counter 2, 3; 1/2, 1/4, 1/16, 1/64 of osc oscillation clock frequency serial 2: synchronous type / multi-master i 2 c 1 clock source 1/2, 1/4 of system clock frequency; pulse output of timer counter 3, 4; 1/2, 1/4, 1/16, 1/32 of osc oscillation clock frequency serial 3: synchronous type / single-master i 2 c 1 clock source 1/2, 1/4 of system clock frequency; pulse output of timer counter 4, 5; 1/2, 1/4, 1/16, 1/32 of osc oscillation clock frequency serial 4: synchronous type / uart (full-duplex) 1 clock source 1/2, 1/4 of system clock frequency; pulse output of timer counter 0, 5; 1/2, 1/4, 1/16, 1/64 of osc oscillation clock frequency mad00053aem max. transfer cycles: 255 starting factor: various types of interrupt, software transfer mode: 1-byte transfer, word transfer, burst transfer dma controller (automatic data transfer)
pin assignment tqfp080-p-1212d * lead-free MN101CF95F mn101cf95g mad00053aem special ports buzzer output, remote control carrier signal output, high-current drive port i/o pins 67 common use specified pull-up resistor available input/output selectable (bit unit) i/o 10-bit 11-ch. (with s/h) a/d inputs support tool in-circuit emulator px-ice101c/d + px-prb101c95-tqfp080-p-1212d tm7a / irq5 / p25 irq4 / p24 irq3 / p23 irq2 / p22 irq1 / p21 irq0 / p20 p36 sbt4 / p35 sbi4 / p34 sbo4 / p33 tm3 / p32 tm2b / p31 tm2a / p30 sbt0b / sbt2 / p15 sbi0b / sbi2 / p14 sbo0b / sbo2 / p13 sbt1a / p12 sbi1a / p11 sbo1a / p10 buz / sbt3 / p02 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 an5 / pa5 an6 / pa6 an8 / pb0 an9 / pb1 an10 / pb2 an11 / pb3 dmod vref+ vpp vdd33 vdd18 osc2 osc1 vss xi xo mmod p27 / nrst sbo3 / p00 sbi3 / p01 p75 / sdo5 / tm8 p74 / sdo4 / tm7b p73 / sdo3 p72 / sdo2 / sbt1b p71 / sdo1 / sbi1b p70 / sdo0 / sbo1b p43 / key11 p42 / key10 p41 / key9 p40 / key8 p67 / key7 p66 / key6 p65 / key5 p64 / key4 p63 / key3 p62 / key2 p61 / key1 p60 / key0 p54 / tm8 / tm1 / tm0b p53 / tm7 / tm0a / rmc p76 / sdo6 / tm4 p77 / sdo7 / tm5 p87 / led7 p86 / led6 p85 / led5 / sbo0a p84 / led4 / sbi0a p83 / led3 / sbt0a p82 / led2 p81 / led1 p80 / led0 p44 / key12 p45 / key13 p46 / key14 p47 / key15 vref- pa0 / an0 pa1 / an1 pa2 / an2 pa3 / an3 pa4 / an4
MN101CF95F, mn101cf95g mad00053aem
request for your special attention and precautions in using the technical information and semiconductors described in this material (1) an export permit needs to be obtained from the competent authorities of the japanese government if any of the products or technical information described in this material and controlled under the "foreign exchange and foreign trade law" is to be exported or taken out of japan. (2) the technical information described in this material is limited to showing representative characteristics and applied circuits examples of the products. it neither warrants non-infringement of intellectual property right or any other rights owned by our company or a third party, nor grants any license. (3) we are not liable for the infringement of rights owned by a third party arising out of the use of the technical information as described in this material. (4) the products described in this material are intended to be used for standard applications or general elec- tronic equipment (such as office equipment, communications equipment, measuring instruments and house- hold appliances). consult our sales staff in advance for information on the following applications: ? special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combus- tion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. ? any applications other than the standard applications intended. (5) the products and product specifications described in this material are subject to change without notice for modification and/or improvement. at the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date product standards in advance to make sure that the latest specifica- tions satisfy your requirements. (6) when designing your equipment, comply with the guaranteed values, in particular those of maximum rat- ing, the range of operating power supply voltage, and heat radiation characteristics. otherwise, we will not be liable for any defect which may arise later in your equipment. even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (7) when using products for which damp-proof packing is required, observe the conditions (including shelf life and amount of time let standing of unsealed items) agreed upon when specification sheets are individually exchanged. (8) this material may be not reprinted or reproduced whether wholly or partially, without the prior written permission of matsushita electric industrial co., ltd. 2003 sep
|
